← vanagon.com home · Continue the discussion in the forum
VanagonEuroVan
Sort by authorSort by posting dateSort by topicChronological orderMost recent firstShow authorHide authorShow table of contentsHide table of contentsBack to main VANAGON pageJoin or leave VANAGONSearch
Subject:Re: Where to get a decent paint job? (long)
From:Jim Felder <jim.felder@GMAIL.COM>
Date:Wed, 29 Apr 2015 16:53:48 -0500

I have done this exact thing, and you can't tell those windows from the
ones where I replaced the rubber. I used paracord from harbor freight, and
used a hooked puller to pull the seal up.

Jim

On Wed, Apr 29, 2015 at 4:19 PM, Stuart MacMillan <stuartmacm@gmail.com>
wrote:

> It's all about the prep.
>
> If you are not removing all the windows, try an old school trick before
> you drop it off. Get some cotton cord about 1/8" diameter and use a plastic
> knife to lift up the edge of the window rubber and stuff that cord under
> it.  It will lift the rubber (unless it's hard as a rock) off the body
> preventing that hard paint edge that often starts to peel after a paint
> job.  It also makes sanding and masking easier, and allows the paint to
> come up under the rubber a bit.
>
> Tape one end of the cord to the window for pulling it out later, and pull
> it out by pulling towards the inside of the window.
>
> If you are painting the top too now is a good time to remove the seals for
> painting and get new ones.  You can take off the front part and they can
> paint it on a rack. You'll eliminate another hard paint edge. Get new SS
> screws to re-install.
>
> If you do some of the prep like this, you'll likely be happy with the
> job.  But if you have rust under the window rubber, you should remove the
> window and clean it all out first.
>
> Stuart
>
> -----Original Message-----
> From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf
> Of PB
> Sent: Wednesday, April 29, 2015 12:45 PM
> To: vanagon@GERRY.VANAGON.COM
> Subject: Where to get a decent paint job? (long)
>
> I've been asking around about the cost of a paint job.  The first body shop
> I asked told me it would cost $7,000 and suggested that I try Maaco, so I
> went to 2 Maaco's - only about a mile apart!
>
> The first guy told me that all I needed was their basic paint job at a cost
> of $1,300, including fixing a small dent at the front driver side signal
> light area.  About 6 years ago my husband took his badly dented 1996 Camaro
> there and was very pleased with their work, service, and pricing.
>
> As I was arriving at the SECOND Maaco, a beautifully painted 2-tone car
> with a graphic design on it was leaving out the driveway. In the shop there
> was a beautifully painted red and white VW Camper pop-top BUS that they had
> just restored.  He suggested  their best paint job at a cost of $2,000,
> including color, sand, and buff.
>
> I don't mind paying an extra $700 if the quality would is greatly superior
> to the econo job. Neither of the guys tried any hard sell tactics, and took
> their time explaining and answering all of my questions.
>
> Does anyone have experience with Maaco or any other "econo" paint places?
> I can't do any prep by myself, and not willing to pay several $,$$$'s.
>
> Description of Maaco basic paint jobs
> <http://www.maaco-vannuys.com/auto_paint.html>
> Maaco Platinum Paint Job
> <http://www.maaco-vannuys-north.com/auto_paint.html>
>
> Patti
> 90 Westy Automatic
> Los Angeles
>
>
>
> --
>
> *♪♫**♥**♫♪♪♫**♥**♫♪♪♫**♥**♫♪♪♫**♥**♫♪*
> If it's not on my Smart Phone, it doesn't exist...
> ●▬▬▬▬▬▬ஜ۩۞۩ஜ▬▬♥▬▬▬ஜ۩۞۩ஜ▬▬▬▬▬●
>

← Previous in threadNext in thread →
Back to April 2015, week 5
Have something to add on this topic today? Revive this thread in the forum »